TOTOLINK Support Page
1.How to Change login Password?
2.How to change SSID of EX200 ?
3.How to Check Current Gateway IP Address
4.How to setup the router to work as a repeater?
5.How to reset the current configuration to factory default ?
Solution:
STEP-1
Connect your computer to the router by cable, then log into the router by entering http://192.168.1.1.
STEP-2
User Name and Password are required, by default both are admin in lowercase letter. Click Login.
STEP-3
First, the Easy Setup page will turn up for basic and quick settings, Click " Advanced Setup ".
STEP-4
Click " Management -> Save/Reload Settings " on the left navigation bar, Click “Reset” button.
Method 2
Only by one click on the " RST/WPS button "
STEP-1.
Press and hold the RST/WPS button for about 10 seconds, until the CPU led blink quickly.
STEP-2.
After nearly 30 seconds, resetting is finished.
6.How to modify the user name and password ?
Solution:
STEP-1
Connect your computer to the router by cable, then log into the router by entering http://192.168.1.1
STEP-2
User Name and Password are required, by default both are admin in lowercase letter. Click Login
STEP-3
First, the Easy Setup page will turn up for basic and quick settings, where you change exist SSID andPassword, then click “Apply button”.
Notice : DO NOT power off the device or close the browser window during the upload because it may crash the system.
7.How to Establish Wireless Connection by WPS Button. ?
8.How to log in the web-configuration interface ?
9.How to configure ADSL router's easy setup ?
10.How to log into N100RE and N200RE New User Interface?
11.How to upgrade the firmware of the (N150RB, N300RB) Routers?
Solution:
STEP-1.
Connect your computer to the router
1-1. Connect your computer to the router by cable or wireless, then login the routerby entering http://192.168.1.1 into the address bar of your browser.
1-2. Please login to the Web Setup interface (the default user name and password is admin).
STEP-2.
Click Firmware Upgrade on the navigation bar on the left.
STEP-3.
Click Choose File button to select the firmware version and then click Upgradebutton. After the router reboots, upgrade is finished.
[ Notice ] DO NOT power off the device or close the browser window during the upload because it may crash the system.
12.How to upgrade the firmware of the CP300 Routers?
Solution:
STEP-1
Connect your computer to the router by cable, then log into the router by entering http://192.168.1.1
STEP-2
User Name and Password are required, by default both are admin in lowercase letter. Click Login.
STEP-3
Click " System -> Upgrade Firmware " on the left navigation bar.
STEP-4
Click " Choose File " button to select the firmware version and then Click " Upload button ". After the router reboots, upgrade procedure finished.
Notice : DO NOT power off the device or close the browser window during the upload because it maycrash the system.
13.How to upgrade the firmware of the N300RH Routers?
14.How to upgrade the firmware of the (N300R+, N302R+) Routers?
15.How to login to extender by manually configuring IP. ?
16.How to manually set an IP address ?
17.How to disable SSID broadcast ?
Solution:
In order to improve network security, you can disable SSID broadcast in the web-configuration interface. After disabled SSID broadcast, other devices can find and connect to the SSID again.
STEP-1
Connect your computer to the router
1-1 Connect your computer to the router by cable or wireless, then login the routerby entering http://192.168.1.1 into the address bar of your browser.
Then press Enter key (If it prompts an error connection, please restore to factory settings).
1-2. It will show up the following page that requires you to enter valid User Name and Password:
Enter admin for User Name and Password, both in lower case letters.
Then click OK button or press Enter key.
Now you have logged into the web interface of the router.
STEP-2
Click Wireless Settings-> Wireless Basic Settings
On this page, you could change the SSID Broadcast status.
18. How to change LAN or WLAN ip of the router for N300R Plus, N300RA, N300RB, N302R Plus and N303RB ?
Solution:
IP conflict may happen while there are two routers in series connection or other reasons, which maycause false connection.
Change LAN IP by follow steps can help you avoid of IP conflict.
Step-1
Connect your computer to the router
1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.
1-2. Please click Setup Tool icon to enter the router’s setting interface.
1-3. Please login to the Web Setup interface (the default user name and password is admin).
STEP-2.
Click Advanced Setup->Network->LAN/DHCP on the navigation bar onthe left.
STEP-3.
Alter LAN IP into 192.168.X.1 (“X” is in range of 2~254, e.g.192.168.3.1),and then click Apply& Restart button.
STEP-4.
Wait for 40 seconds until the progress bar finished and then you should use the new address to enter the setting interface later.
19. How to change LAN or WLAN ip of the router for N100RE, N200RE, N150RT and N300RT?
Solution:
IP conflict may happen while there are two routers in series connection or other reasons, which maycause false connection.
Change LAN IP by follow steps can help you avoid of IP conflict.
Step-1
Connect your computer to the router
1-1. Connect your computer to the router by cable or wireless, then login the router by entering http://192.168.1.1 into the address bar of your browser.
1-2. Please login to the Web Setup interface (the default user name and password is admin)
STEP-2.
Click Network Settings->LAN/ DHCP Server on the navigation bar on the left. In this interface you can change the IP address (e.g. 192.168.1.2),and click Apply button for saving settings.
20.How to set up the remote login router web interface ?
21 .How to upgrade firmware of the extender ?
Solution:
It is suitable for EX150, EX300
STEP-1
Please login the extender’s web-setting interface. (Default IP address: 192.168.1.254, User name: admin, Password: admin)
STEP-2
Click Firmware Upgrade on the config explorer.
STEP-3
Click Choose File button to select the firmware version and then click Upgrade button.
